How to Use Multiple Speakers On one Home theatre Or Stereo Amplifier

This is ultimately easy, but before explaining the process I feel it is necessary to provide a warning. Multiple sets of speakers usually can not be addicted with the a standard audio amplifier without some sort of impedance matching device. This is in reference to those persons whom might want to run speakers in several rooms at the same time (distributed audio). If several sets of speakers are run in set of speaker terminals the amplifier in most cases overheat and close, and may blow the output stage (see footnote 1). These statements do not sign up for PA style amplifiers with 25 or 70 volt outputs, which خرید اسپیکر require special speakers with transformers.

The correct solution is to apply either an impedance matching speaker selector with the protection made it possible for, or use impedance matching in wall volume controls. Notice the underline in the sentence in your essay above. This is because most speaker selectors are made with a dangerous feature: a button, right in front, to disable the protection. If the switch was in back to prevent unintended deactivation of the speaker protection it would be much better. If the protection is accidentally switched off while running multiple twos of speakers the amplifier will close, may blow output fuses, and well may damage the output stage of the amplifier. There are really only 2 reasons to turn this switch off, the most relevant being that impedance matching volume controls are usually now being applied to ALL twos of speakers. The other reason would be only if one pair of speakers are usually now being run, making impedance matching unnecessary. In this event, though, leaving the protection switched in will make very small difference to the sound, exactly why would someone not leave it on?

Remember it this way: only put one speaker per pair of terminals (usually red and black) on the amplifier. Do not try to use a besieg amp to feed several rooms with one room on the center, one room on the rear is all around etc. This is due to the way a besieg individual distributes the sound as you may end up with only the voice in one room and only the music in another! The correct hookup for a besieg individual puts besieg sound in the main room and sound from the left and right main speakers is distributed. My recommendation for hooking up a besieg individual is just as follows. Run the speaker selector from the front left and front right outputs on the amplifier. Hook your front left & right speakers to the first speaker switch on the speaker selector. You will need to re-balance your besieg system by running the pink noise test as the speaker selector will decrease the output to the left and right speakers by a small amount. Web template running the main speakers & the other speakers powering the speaker selector without one set being louder than the others. If your speaker selector has volume controls, you need to make sure when you use your besieg system for movies the volume control has reached the same setting it was when doing the pink noise test. You may hook the speaker selector to the ‘b’ speaker switch on the amplifier if speaker volume balance between your main left & right speakers and the rest of the speakers is not an issue.

Another variation is amplifiers with a direct speaker output for zone 2, 3, etc. These are set up to drive 1 pair of speakers, and is employed with impedance matching if more twos can be used. The zone outputs allow a second (or third etc) source, for example CD in one room and radio in another.

An impedance matching speaker selector provides multiple outputs in input, and protects your amplifier from damage. Speaker selectors come with 4-12 outputs. As long as your amp has enough power, you can push as many sets of speakers as you want. Simply connect the speaker selector to your ‘A’ (or ‘B’) outputs and the rest of your speakers on the speaker selector. You can purchase speaker selectors with volume controls for each individual speaker. Another option is in wall impedance matching volume controls, which require no speaker selector. Most of these are set with jumpers at install time, providing the correct matching. If you want to run more twos of speakers than the speaker selectors or volume controls are made for (usually 12 twos max. depending on the hardware) you probably want a second amplifier to run the second set of volume controls (or speaker selector) from.

So, what is impedance and impedance matching? (Warning: partially technical material ahead)

The music signal to your speakers is called alternating current (or AC), because it varies polarity and voltage. This is in comparison to a battery, for example which produces a reliable, or direct current. You may picture current as the amount of water flowing in a water pipe (the wire) and voltage as the water pressure. Alternating current can be imagined as a flow that reverses direction and direct current as a steady flow in one direction. The analogy is not exact but is close enough to get a picture of what is happening. Standard house current in the us alone reverses direction (polarity) at an interval (or frequency) of 60 times per second, measures as 60 Hz (Hertz). If you visit our site you can see this article with explanatory diagrams included.

Your speakers have a certain amount of resistance to current. Imagine the resistance as a constriction in the water pipe, reducing the flow. They have a DC resistance, termed the voice coil resistance, and resistance to AC is called impedance. Resistance and impedance values are measured in Ohms. Impedance is a complex sum of dc resistances, plus the resistance to various AC frequencies caused by capacitance and inductance (normal properties of electrical and electronic devices). It is usually specified for speakers as nominal impedance, and is referenced to particular frequencies. However, Consider than it as resistance to AC for practical purposes. Enter into the esophagus rated at either 8 or 4 Ohms. Most home amplifiers prefer an 8 ohm impedance. Each time another speaker is added in parallel the impedance is reduced. Visualize several pipes connected together to the same pump, obviously the flow from the pump increases (up to the limit of the pumps capability). The amplifier is the pump. Two 8 ohm speakers reduce the impedance to 4 ohms, four 8 ohm speakers reduce the impedance to 2 ohms, and so forth.

An amplifier expects (most require) a certain amount of resistance to current flow. The reduced the impedance, the more current flows through the output stage of a typical amplifier. This usually flows directly by having a transistor (or other amplifying device) and damages the transistor or protective resistors in the output stage. If you get lucky it only blows an output stage merge. The meaning of the story is always use an impedance matching speaker selector, (or volume control) and your amplifier will always see a safe impedance load.

Leave a comment

Your email address will not be published. Required fields are marked *